Book a Consultation
Water beading and running off the coated paint of a red supercar

Ceramic Coating Aftercare & Washing Guide

Look after your coating properly.

Your Feynlab coating is designed to last years, but how you wash the car matters. This is the exact procedure and the exact products Paul recommends to every client after a ceramic coating. Follow it and the coating will perform the way it should.

Why it matters

The golden rules.
Never break them.

Feynlab coatings are built to last years, but they’re not maintenance-free. The biggest threat to a ceramic coating isn’t road grime or weather: it’s incorrect washing. Wrong products, wrong technique or washing in direct sunlight can degrade the coating faster than anything the road throws at it.

The guide below is exactly what Paul sends every client after their coating is applied. The products are specifically chosen for Feynlab-coated cars. Use them, follow the procedure, and the coating will continue to perform and look the way it did when it left the studio.

  1. I

    Never wash in direct sunlight

    Always wash in the shade or on an overcast day. Sunlight causes shampoo and water to dry on the panel before you can rinse it, leaving marks in the coating that are difficult to remove.

  2. II

    Always wash top to bottom

    Start at the roof and work down. The lower panels carry the most contamination: always clean them last to avoid dragging grit up onto cleaner upper surfaces.

  3. III

    Always wash in straight lines

    Never use circular motions. Straight lines, front to back or top to bottom, prevent swirl marks from being induced in the paint during washing.

  4. IV

    Always use the two bucket method

    One bucket for your shampoo solution, one with clean water to rinse the wash mitt between panels. Grit guards in both buckets. This keeps contamination out of the wash solution and off the paint.

  5. V

    Use Feynlab Pure Wash only

    Only use Feynlab Pure Wash shampoo on a ceramic-coated car. Generic shampoos can strip or dull the coating over time. Pure Wash is pH neutral and formulated specifically for coated surfaces.

  6. VI

    Finish with Hybrid Detailer

    After every wash, apply Feynlab Hybrid Ceramic Detailer to each panel. This tops up the coating with every wash, maintaining the gloss and protection between annual inspections.

The procedure

Eight steps. Every wash.

Water beading on a coated blue panel
  1. Rinse or snow foam first

    Before the wash mitt touches the car, rinse the vehicle thoroughly with a pressure washer or apply snow foam to loosen surface contamination. Never put a dry mitt on a dry car: even small particles of dust can scratch the paint.

  2. Set up your two buckets

    Fill one bucket with warm water and Feynlab Pure Wash shampoo. Fill a second bucket with clean water for rinsing the wash pad between panels. Put a grit guard in the bottom of each bucket. The grit guard traps contamination at the bottom so it doesn’t transfer back to the mitt.

  3. Wash one section at a time, top to bottom

    Work in sections: roof and windscreen first, then upper panels, then lower panels and sills, leaving the wheel arches and lower bumpers to last. After each section, rinse the wash pad thoroughly in the clean water bucket before returning it to the shampoo solution. Always wash in straight lines. Never circular motions.

  4. Clean the wheels

    Wheels carry the heaviest contamination: brake dust, road tar and grime. Use Feynlab Tyre and Wheel Cleaner with a dedicated wheel brush for the face of the wheel and an EZ Detail brush for the inside of the barrel. Never use the same mitt on the wheels that you use on the paint.

  5. Rinse the whole car thoroughly

    Once the full car and wheels are washed, rinse everything thoroughly: roof to sills, wheels and arches. Make sure all shampoo residue is removed before drying begins.

  6. Dry with a quality drying towel

    Use the Rag Company Liquid8r twisted loop microfibre drying towel: it’s the one Paul uses and recommends. Work panel by panel, top to bottom. Once the main panels are dry, blow out all the crevices, door shuts, mirror housings and badges with a forced air dryer to prevent water marks appearing after the car is put away.

  7. Apply Feynlab Hybrid Ceramic Detailer

    This is the step most people skip, and it’s the most important one for maintaining the coating long term. Shake the bottle well for a full minute before use. Spray one or two sprays onto each panel and buff with an Edgeless 365 microfibre. Work panel by panel. The Hybrid Detailer adds a fresh layer of ceramic protection with every wash, keeping the gloss deep and the water beading sharp.

  8. Tyre dressing: Feynlab Black Velvet

    For the finishing touch, apply Feynlab Black Velvet Tyre Sealant using a microfibre applicator. Wear rubber gloves: it can be messy on your hands. Black Velvet gives a deep, satin tyre finish and seals the rubber for lasting protection and appearance.

Products at a glance

Everything you need. Nothing you don’t.

  1. Shampoo

    Feynlab Pure Wash

    pH neutral shampoo formulated specifically for ceramic-coated vehicles. The only shampoo Paul recommends on a Feynlab-coated car.

  2. Maintenance Detailer

    Feynlab Hybrid Ceramic Detailer

    Tops up the coating with every wash. Shake for one minute before use: this is not optional. One to two sprays per panel, buff with a quality microfibre.

  3. Wheel & Tyre

    Feynlab Tyre & Wheel Cleaner

    Safe on all wheel finishes including diamond cut and powder coat. Effective on brake dust and road contamination without aggressive acids.

  4. Tyre Dressing

    Feynlab Black Velvet Tyre Sealant

    Deep satin finish and lasting tyre protection. Apply with a microfibre applicator. Wear gloves: it stains hands. Worth every bit of the effort.

  5. Wash Pad

    GT Wash Pad

    The wash pad Paul uses. Soft enough for coated paint, structured enough to hold shampoo solution and release contamination safely into the rinse bucket.

  6. Drying

    Rag Company Liquid8r Drying Towel

    Paul’s recommended drying towel. Twisted loop construction absorbs water fast without dragging on the surface. Use with an air dryer for perfect results.

  7. Air Dryer

    Blo Air Dryer

    Essential for blowing water out of door shuts, badges, mirrors and crevices after washing. Prevents the water marks that appear hours after a wash.

  8. Microfibre

    Rag Company Edgeless 365

    The microfibre Paul uses to apply and buff the Hybrid Detailer. Premium edgeless construction: no risk of scratching from hard edges. One side to apply, one side to buff.

Google Reviews

What clients say about Paul.

5.0

Google rating · 139 reviews

  • “I was thunderstruck by the effect Paul achieved. I am certain the car never looked, or felt, this good, not even the day it came out of the showroom. The depth of the shine has to be seen to be believed. I consider myself very fortunate to have discovered Paul.”
    G Verified customerGoogle review
  • “Paul did an awesome job on my TT and my Q7. The Q7 needed a lot of work and now looks like new. Really worthwhile investment in upgrading and protecting both cars.”
    DW Duncan WalkerAudi TT & Q7
  • “I had my Mercedes paint corrected and ceramic coated and was blown away with how good the work is. The car looks better than brand new. I’ve seen other detailers’ work and they don’t come anywhere close.”
    AH Anjela HitchcockMercedes
  • “Completely blown away by the level of detail and care put into bringing my car back to better than new finish. Paul communicated with video and photos during the whole process. This guy is at the top of his game: he truly knows his craft and has made it an art form.”
    G Verified customerGoogle review
  • “I brought my 12 year old Audi TT to Paul in a sorry state. A week later the transformation was truly miraculous. A deep shine has been restored and the paintwork has a mirror-like finish. He makes the impossible seem possible.”
    WS William SandefordAudi TT
  • “Paul Dalton has been the best known car detailer in this country for many, many years. I was somewhat honoured to partner with him on so many cars of all shapes, sizes and prices. Great guy and still the first call for detailing expertise.”
    S SteveIndustry professional

Book a Consultation

Any questions? Just ask Paul.

If you’re unsure about anything (the procedure, the products, or how your coating is performing) get in touch directly. Paul is happy to advise.

Paul Dalton

Prefer something quicker? Call Paul.

+44 7444 869983

Your car

The work
What would you like done? *

Photos help Paul see the paint before he calls. You can also send them on WhatsApp.

Your details

So Paul can call or WhatsApp you back.

Best way to reach you

A request, not a booking. No deposit, no call centre. Paul replies himself.